Clear Concrete Sealer

Quantity
Clear

$210.00

  • Cost From

    $0.58 per m2

  • Re-Coat

    5 - 8 hrs

  • UV Stable

    Yes

  • Coverage

    5-8m2 per ltr

  • Coats

    2

  • Equipment

    Roller/Broom

  • Dilution

    No

  • Clean Up

    Solvent

Features

  • Hard-wearing & durable. Designed for harsh outdoor environments
  • Protection of surface deterioration from UV, traffic and dirt
  • Produces an extremely low-maintenance surface
  • Darkens and enhances old coloured, stamped/decorative driveways or pavers
  • Brings exposed aggregate concrete to life
  • Reduced hot tyre marking and problematic marring and scuffing
  • Easy to apply with extremely good adhesion to concrete

    Product Description

    Clear Concrete Sealer is a hard wearing, semi-gloss “wet look” sealer that is used for the protection of surface deterioration from UV, traffic and dirt. Formulated to withstand harsh outdoor environments, the quick, hard wearing coating dramatically eases maintenance. It will darken and enhance old coloured stamped driveways or bring to life the exposed aggregate in concrete.

    Clear Concrete Sealer contains additives which help to reduce hot tyre marking while also reducing the problematic marring and scuffing of the sealer. This makes it ideal for use on driveway’s or on its own or as a protective sealer for stamped decorative concrete or concrete pavers. The Right Choice Non Slip Additive can be added for use as driveway sealer or wet area application. An extremely easy product to apply by roller or a solvent resistant broom. Clean-up or thinning (if required) is with the Right Choice Solvent.

    Idea For

    • Exterior Path Ways
    • Driveway’s
    • Garage Floors
    • Concrete Pavers
    • High Traffic Areas

    Coverage Rates

    20 litres will do 2 coats over approximately 60m2 – 70m2 (concrete porosity dependent)

    Coverage rates will be determined by how porous the concrete is (how easily water soaks in). The easier and quicker that water soaks in, the more porous the concrete is and the more product you will use.

    Surface Porosity:

    • Ensure the concrete has sufficient porosity for the sealer to penetrate.
    • Dip a finger into a glass of water and apply 2-3 drops to the surface.
    • Time the amount of time it takes for the water to soak into the concrete.
    • For sufficient porosity to apply a sealer, this should be no longer than 90 seconds.
    • Repeat the test over multiple sections of the concrete substrate.
    • If under 90 seconds then the concrete has sufficient porosity for application of the sealer.
    • If longer than 90 seconds, then it may be necessary to either acid wash or diamond grind the concrete to open it up and create the required porosity.

    Quantity Estimator

    Enter the dimensions of your surface area to estimate how many tins of product you may need:

    Summary Estimation
    0 tins
    * The estimated number of tins is based on the average coverage per square metre and is to be used as a guide only, as there are many variables when estimating (ie, porosity). Please ensure you check your calculations as Right Choice Coatings cannot be held responsible if the incorrect quantity.

    Information Guides

    1. Download: Technical Data Sheet
    2. Download: Preparation Guide
    3. Download: Application Guide
    4. Download: Troubleshooting Guide

    General Notes:

    • Ensure to read the TECHNICAL DATA SHEET, the PREPARATION GUIDE and the APPLICATION INSTRUCTIONS thoroughly first.
    • Generally only two coats are required, however on highly porous surfaces then a third coat may be necessary.
    • It is recommended to do a test patch first to determine the suitability of the product.
    • Ensure that the concrete is a minimum of 28 days old.
    • Do not apply when the ambient temperature is below 15c or above 28c.
    • It is always advisable to apply sealers in the afternoon and in the shade.
    • Do not apply in direct sunlight when the temperatures exceed 28c.
    • The substrate must be cool to touch before applying any sealer or coating.
    • Do not apply if rain is imminent in the following 24 hours of application.
    • Always follow the manufacturer’s guidelines for coverage.

    PREPARATION:

    Surface Porosity:

    • Ensure the concrete has sufficient porosity for the sealer to penetrate.
    • Dip a finger into a glass of water and apply 2-3 drops to the surface.
    • Time the amount of time it takes for the water to soak into the concrete.
    • For sufficient porosity to apply a sealer, this should be no longer than 90 seconds.
    • Repeat the test over multiple sections of the concrete substrate.
    • If under 90 seconds then the concrete has sufficient porosity for application of the sealer.
    • If longer than 90 seconds, then it may be necessary to either acid wash or diamond grind the concrete to open it up and create the required porosity.

    Moisture:

    • The substrate must be dry and free from any rising moisture.
    • Ideally use a concrete moisture meter to determine the moisture content. If this is not available, proceed using the method below.
    • To test for moisture, cut a piece of thick black plastic into 1m².
    • Ensure that it is free from any tears or pinholes (this would render the test useless).
    • Attach the plastic to a section of the substrate (repeat in other areas) & duct tape the edges.
    • It is important that the plastic is completely sealed around all edges and free from holes.
    • After 24 hours, remove the plastic. If the concrete has darkened or there is condensation under the plastic, then the concrete is not sufficiently dry to apply a sealer or coating.
    • If the substrate is not dry enough then either wait a few more days & repeat the test or it may be necessary to use a concrete moisture barrier. Contact Right Choice for advice.

    Contamination:

    • All substrates must be clean and free of contamination i.e. oil, grease, bird droppings etc.
    • Many of these contaminates are easily removed using the Right Choice Concrete Cleaner.
    • In some cases it may be necessary to use a concrete grinder or a light acid wash.
    • Basically, if water does not penetrate through the contamination then neither will a sealer or a coating.

    Acid Etching

    • If required, the concrete can be lightly acid etched prior to sealing. This will help to create a more porous substrate.
    • Use extreme caution and safe handling methods when using hydrochloric acid.
    • Before acid etching, make sure the concrete is cleaned properly of all contaminants, oil, grease and dirt by using the Right Choice Concrete Cleaner (mix @ 50:50 dilution with water), paying extra attention to heavily contaminated areas.
    • Rinse the Concrete Cleaner off thoroughly with clean water.
    • Dilute the hydrochloric acid with water at a rate of 1 part acid to 10 parts water. CAUTION! Always add the acid to the water, not water to acid.
    • Lightly dampen the surface so that the concrete is slightly wet but not puddling water.
    • Apply the diluted solution evenly to the surface using a watering can or similar.
    • Allow the acid to bubble on the concrete for up to 15 mins.
    • Once the bubbling has ceased, thoroughly rinse the surface off with clean water (abide by local laws for disposal).
    • Neutralise the surface using the Right Choice Concrete Cleaner (mix @ 50:50 dilution with water, highly alkaline). Brush the mixture into the surface and allow it to sit for 5-10mins before rinsing thoroughly with clean water.
    • Allow the surface to dry for a minimum of 24 hours (weather dependant).

    *Note – If neutralising is not done correctly, acid etching can leave a white powdery residue, (calcium carbonate) on the dried surface. This is a fine white dust which can cause problems with adhesion and delamination of the coating. Once neutralising is complete, check the entire surface of the concrete. It should have a uniformed texture similar to medium grit sand paper (If not, repeat the above process). Sprinkle a few drops of water over the surface and If all the water is quickly absorbed, the surface is sufficiently oil and grease free. If the water still beads up (even if only in certain areas), then further preparation as above will be required.

    Application:

    • Always wear the appropriate personal protection equipment.
    • Clear Concrete Sealer should be applied using a 10mm nap roller, sprayer or solvent resistant broom.
    • Pour the sealer directly onto the concrete in ribbons, try to avoid pouring in large puddles.
    • Apply the sealer using the “cross hatch” method. Roll East to West and then roll again North to South (right angles to each other). Use this method for all subsequent coats.
    • Ensure to keep “wet edge” of the sealer to avoid any overlapping or roller marks.
    • Keep to the recommended application rate, do not over apply. Two thin coats are better than a single heavy coat.
    • Allow a minimum of 6-12 hours drying time in-between coats (weather dependent).
    • Ensure the first coat is clean and free of any contamination before applying the second coat.
    • Do not walk on for a minimum of 24 hours and allow 3 days before driving over.

    Specifications

    Product Name: Clear Concrete Sealer

    Material: Solvent-Based Acrylic Sealer

    Pack Size: 20 Litres

    FAQ's

    • Q – Is it necessary to use thinners in the 1st coat?
    • A – It really depends on the porosity of the concrete and weather conditions. The idea of the 1st coat is to get it to soak in as much as possible. So if you have a very “tight slab” (not very porous), then you would dilute the 1st coat with 30% xylene (solvent) and then do 2 more coats neat. The same if it is hot, dilute the 1st coat for better penetration. If the slab is very porous (water soaks in easily), then there is no need to prime, however you may need to do 3 coats in total. 

    24 reviews for Clear Concrete Sealer

    1. John Sebastiani (verified owner)

      Went on nicely and brought the colour out of the Pavers.

      Helpful?
      0 0
    2. Sutherlands Property Management (verified owner)

      Excellent Product

      I did a small section of a driveway that continually gets heavy with black Mould. Once the area was cleaned it was easy to apply. First coat, the old concrete soaked the product up. The dried look has a matt finish which looks fantastic.

      Side Note: get to any spills or splashes immediately or it will set quickly and leave a mark.

      Much superior product than others I have used in the past.

      Helpful?
      2 1
    3. Mike Hilder (verified owner)

      Great Results

      Had the driveway pressure cleaned and applied Right Choice sealer and looks like new. Fast service and product did the rest. Very happy.

      Helpful?
      0 0
    4. Shayne Newham (verified owner)

      Great product

      Waited for weather to come good and sealed stamped concrete driveway and large alfresco. Would have been at least 10 years since last sealed. Easy product to use and the results are amazing. Could not believe the concrete colour would come out so good. Will use the product again.

      Helpful?
      1 0
    5. Christine Billsborough (verified owner)

      Clear Concrete Driveway Sealer

      We had a huge job to do with driveway, pathways around the house, and another concrete slab at the back.
      After doing research on line we chose your product as it stood above other brands.

      Our driveway and pathways are seventeen years old and after cleaning and using your product, they have come up like new and we are so happy with the end result.

      Helpful?
      1 0
    6. Christine Billsborough (verified owner)

      Clear Driveway Sealer

      I did make the right choice when I chose your product to re seal our patterned coloured driveway, and other exposed agrigate pathways.
      We are so pleased with the result, it has brought out the colours and makes them look new again, so we are buying more to do other things.

      Helpful?
      0 0
    7. Stephen Barratt (verified owner)

      Very easy to apply and works well

      We used this on top of the non slip driveway paint and so far it looks good. Two coats with non slip additive to the first coat. It darkens normal concrete but not paint (which was a mistake of ours). Very easy to use and fantastic grip in the wet. Our driveway has quite a slope and even natural concrete can get slippery in the wet and a high leaf drop area.

      Helpful?
      0 0
    8. peter coskerie (verified owner)

      Concrete sealer

      Excellent service and excellent product

      Helpful?
      0 1
    9. Gary Jones (verified owner)

      Hassle free transaction with no delays. Sealant was exactly what I needed.

      Helpful?
      2 0
    10. Nigel Cunningham (verified owner)

      The team were super responsive to email answered all my questions . Fast Delivery and our driveway looks probably better than it did NEW 10 years ago . Really rate this team and product

      Helpful?
      0 0
    11. Ross Spring

      I recently purchased the clear concrete sealer (20 litres). I was impressed by the quality and ease it was to put on as I have used plenty of dealers over the last 10 yrs. Time will tell with the length of time that the product lasts. I also contacted support after the first coat and they replied within an hour which is excellent service.

      Helpful?
      0 0
    12. Pat Boland

      I have been using Right Choice for several years now, products and service has always been great. I have just used this sealer for the 1st time and like everything else it has performed extremely well. Thanks guys

      Helpful?
      0 0
    13. Nicola (verified owner)

      I used both the non slip paint and sealer on my patio and in my garage. What a fantastic result. They look beautiful and I am really happy.
      A high quality product that I would highly recommend .

      Helpful?
      0 0
    14. Ann-Marie Verity

      Extremely fast delivery, arrived within days from interstate, great product and what amazing value for money, will look no further for future purchases. Thank you to those that took the time to review as I based my purchase on your comments.

      Helpful?
      0 0
    15. Jason (verified owner)

      Fast delivery, driveway is back to brand new, has a great fresh wet look so everyone can tell you’ve done it

      Helpful?
      1 0
    16. Mario

      arghhh, it worked too well! Now I have to do all of the path ways to match 🙁

      Helpful?
      0 0
    17. Phillip

      Delivery was good and the product as described. Will definitely use again and recommend to friends. Thank you

      Helpful?
      0 0
    18. Frank Simmons

      I am selling my house and I used this on all of the pathways and on the driveway. It made the house look so much better.

      Helpful?
      0 0
    19. Wendy

      We used this on our driveway and it looks great.

      Helpful?
      0 0
    20. Jack

      Very easy to use. Bought my coloured driveway back to life. Delivery was fast 🙂

      Helpful?
      0 0
    Add a review
    Review our product to get a chance to receive coupon!

    Your email address will not be published. Required fields are marked *